Just How to Replace a Bathtub Yourself: Removing and Replacing.
Just How to Replace a Bathtub Yourself: Removing and Replacing.
Blog Article
They are making a number of good observations on A Step-by-Step Guide to Installing a Bathtub as a whole in the content underneath.
Mounting a bathtub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably hard task. If the old tub is easily easily accessible, the project can move quickly; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Ensure you have qualified on your own for the task as well as are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed task, it is far better to consider using one before you start. Opportunities are you might need a professional plumber to make tube connections.
This post will help you install a brand-new bath tub in your restroom if you have actually currently gotten a new tub as well as do not need to alter the plan of your previous water supply pipes.
Your tools as well as material checklist need to comprise the following:
Getting ready for the Installation
Firstly, the supporting frame provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps system to avoid stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing faucets can be fairly problematic due to the restricted accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before going on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, put the tub in the needed placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bathtub till the spirit level checks out level.
To set up taps, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and check all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has actually been made use of at the very least when as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Protect the faucet in position with the producer offered backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with dampness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that article about How to Install a Bathtub Yourself while browsing on the internet. Are you aware of another person who is interested in the topic? Please feel free to share it. Thanks for your time. Kindly visit our website back soon.
Schedule A Free Estimate Report this page